《一》 流程
開機復位
機器初始化——進入連機狀態，顯示走刀速度、曲線速度
按功能切換鍵——進入手動操作顯示X、Y坐標
同上——進入對刀操作，顯示抬落變化Z軸坐標
同上——進入多功能操作，顯示原點、零點、重刻、自檢
同上——機器初始化
《二》 使用及操作
1． 使用（手動按鍵操作）
按鍵說明
（1） 復位鍵：打開電源使機器復位進入連機狀態，復位后機器回到初使?fàn)顟B(tài)，并默認當前點為原點。
（2） 連機狀態下、按鍵
X+曲線速度增大（2-30）X-反之。Y+曲線速度增大（2-70m/s）Y-反之
（3） 功能鍵（模式鍵）
A按鍵顯示X、Y坐標 B再按進入對刀、顯示Z軸 C 按進入多功操作
按X+（）刻刀右移 按Y+刀上抬 按X-刻刀回原點
X-（）刻刀左移 Y-刀下移 X+進行一次自檢雕刻
Y+（）刻刀前移 按確認鍵可調整抬落量 Y-回物理原點
Y-（）刻刀后移 確認鍵重復
按確認鍵當前點為原點X、Y清零。 D再按返回連機狀態
（4） 工作中確認鍵為急停鍵按下可使機器立刻停止工作，再按恢復。
2． 操作
1） 裝刀
A將刀裝入夾頭先用手?jǐn)Q緊，再用扳手?jǐn)Q緊。
B把主軸電機調在低速檔打開電源讓刻刀旋轉起來，看刀尖是否跟不旋時一樣尖，否則沒裝正重裝。
2) 電腦排好版，點擊版面[雕]——點擊[雕刻輸出]
3）對刀
按功能鍵（模式鍵）進入對刀操作（詳看按鍵說明）當?shù)都饪旖咏婷鏁r(shí)確認鍵選用較小抬落量轉起主軸直到刀尖剛好接觸版面（工作中也可使用調整雕刻深度）。
備注：對刀的目的是為了將雕刻機的Z軸起始加工點告訴電腦。
4）點擊版面上[開始]
5）重復操作
在機器處于功能狀態時按確認鍵機器即對上次輸出文件進行重刻。
6）返回原點
當遇到斷刀需要重刻或其他狀況中斷，進入功能按X –刻刀返回原點。
Ⅰ.Procedure
Replacement
Machine initialization—enter online status, show cutter speed and curve speed
Press function exchange button—enter manual operation and show X and Y coordinate.
Press function exchange button—enter cutter align operation, show lifting variable, Z
coordinate
Press function exchange button—enter multi-function operation, show get back to origin, zero,
Newly engrave, automatically check.
Press function exchange button—machine initialization
Ⅱ.Direction for use and operation
1. Direction for use (manually key-press)
1).key-press direction
① Replacement key: switch on the power to make the machine enter into online status, the machine get back to origin status after replacement, to make the presently point as zero.
② Press key when online
The speed of X+curve heightened (2-30） X-contrarily.
The speed of Y+curve heightened (2-70m/s） Y-contrarily
③ Function key (mode key)
A press key to show X, Y coordinate B press again, enter cutter aligning, show Z axis C press, enter multi function operation
Press X+( ) cutters shift right press Y+ cutters elevated Press X- cutters get back to zero
X- ( ) cutters shift forward Y-cutter shift down X+ automatically check operation
Y+( ) cutters shift forward press confirmation key elevate height Y-back to physics zero
Y-( ) cutters shift backward confirmation key repeat
Current point is origin after press confirmation key, X, Y no point. D press back key to enter online status
④Confirmation key is stop key when working, this key can make machine to stop immediately, press to return
Ⅲ. Operation
1). Install cutter
A Put the cutter into holder and fix it tightly, then use spanner to tighten.
B Adjust the spindle motor at the lower speed, switch on the power to make the cutter rotary, to see whether the knifepoint is the same as it is not rotary, or else install it once again.
2) Use computer to make up, click the page—click (engrave output)
3) Cutter aligning
Press this function key (mode key) enter cutter aligning operation (detailed pls see key instruction) when knifepoint approach to page, use confirmation key to choose small elevate height to rotary spindle until the knifepoint just touch the page ( also can adjust engrave depth when working).
Note: The purpose of cutter aligning is to tell computer the process point of Z axis.
4).Click page to (start)
5) Repeat operation
When the machine is in function status, press confirmation key to renew engrave.
6) Return to zero
When meet cutter failure or other conditions, enter function press X-cutter back to zero
本公司專業生產木工雕刻機，為您提供專業的雕刻機知識，歡迎廣大客戶，電話：-濟南銘龍
網站客服
